Tomei Japan
Tomei Japan
Tomei Japan PROCAM 4B11 EVO10 IN 280-11.5mm
SKU: 146C280115
•
MPN: 146C280115
•
Condition: Brand New (Factory Sealed)
€234.95
incl. 19% EU VAT • plus shipping
Available to Order • Dispatch in 3–4 Weeks
Flat-rate €14.95 Tracked EU Delivery (Free on orders over €250.00)
Dispatched from JDM Part Shop Europe GmbH (Berlin Warehouse)
CAMSHAFT 4B11
CAMSHAFT
PRODUCT INFO
| TYPE | APPLICATION | DURATION（°） | MAX CAM LIFT（mm） | IN/EX | P/N | ||||
|---|---|---|---|---|---|---|---|---|---|
| ENGINE | MODEL | IN | EX | IN | EX | ||||
| R | 4B11 | CZ4A Evo.10 | 260 | 250 | 10.30 | 9.80 | IN & EX Set | 143059 | |
※PRESET VALVE TIMING
※STOCK VALVE SPRING COMPATIBLE
※The best MIVEC performance settings for the 4B11 TYPE-R PONCAMS（See below for details）
| APPLICATION | DURATION（°） | MAX CAM LIFT（mm） | IN/EX | P/N | 備考 | |
|---|---|---|---|---|---|---|
| 4B11 | 260 | 10.30 | IN | 146C260103 | PONCAM | |
| 250 | 9.80 | EX | 146D250098 | PONCAM | ||
| 270 | 11.50 | IN | 146C270115 | |||
| 11.00 | EX | 146D270110 | ||||
| 280 | 11.50 | IN | 146C280115 | |||
| 11.00 | EX | 146D280110 |
FEATURE / SPEC
■ Duration
The best MIVEC performance settings for the 4B11 TYPE-R PONCAMS.
The description beloew was the best MIVEC setting that TOMEI found during the engine bench test.
Actual settings will vary from car to car depending on the cars location and setup.
| 4B11 PONCAM TYPE-R RECOMMENDED VALVE TIMING | |||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| ENGINE SPEED | 2500 | 3000 | 3500 | 4000 | 4500 | 5000 | 5500 | 6000 | 6500 | 7000 | 7500 | ||
| IN | CENTERLINE SETTING 112° |
ADVANCED | 25 | 25 | 25 | 25 | 25 | 20 | 15 | 8 | 6 | 5 | 0 |
| ADVANCED CENTER | 87 | 37 | 87 | 87 | 87 | 92 | 97 | 104 | 106 | 107 | 112 | ||
| EX | CENTERLINE SETTING 120° |
ADVANCED | 30 | 30 | 30 | 27 | 24 | 18 | 14 | 7 | 2 | 0 | 0 |
| ADVANCED CENTER | 90 | 90 | 90 | 93 | 96 | 102 | 106 | 113 | 118 | 120 | 120 | ||
* The 4B11 Type-R test is based on 100 Octane RON fuel at each RPM range. Advanced settings is required for optimum results.
■ SPEC
| ENGINE | Duration | Max Cam lift (mm) | IN/EX | Max Valve lift （mm） | Cold Valve Clearance （mm）［±0.01］ |
Valve Timing Centerline (Deg) |
Base circle | Note |
|---|---|---|---|---|---|---|---|---|
| 4B11 | 260 | 10.30 | IN | 10.10 | 0.20 | 112 | 34.4 | PONCAM |
| 250 | 9.80 | EX | 9.50 | 0.30 | 120 | .36.4 | PONCAM | |
| 270 | 11.50 | IN | 11.30 | 0.20 | 34.4 | |||
| 11.00 | EX | 10.70 | 0.30 | 36.4 | ||||
| 280 | 11.50 | IN | 11.30 | 0.20 | 34.4 | |||
| 11.00 | EX | 10.70 | 0.30 | 36.4 |
Theme of TOMEI CAMSHAFT
Asymmetrical G-Controlled Profile
 |
When opening the intake valve during high acceleration the G from the camshaft requires to send as much mixture to the cylinder in the shortest time possible. However if the speed is too high it can damaged the Valves, Valve Seats and Valve Springs if the Acceleration G is too high. The Asymmetrical profile design given to the camshafts will allow the Intake and Exhaust Valves to fulfill the target requirement with the wider duration and high lift without damaging the Valve System. |
Maximizing the Valves Efficiency
The general purpose of engine tuning is to change the torque characteristics of the engine by changing the cams duration timing and cam lift amount for maximum torque and horse power. However tuning the engine is not only based on that. When going into finer details by maximizing the Valves efficiency is not just about timing and height lift but to also maximize the intake efficiency. The high valve lift allows huge amounts of air in but at the same time it mechanically damages the valve train and gains added friction loss. Longer cam durations and big cam lifts give deliver more power at higher engine speeds but it also gives a rough idle and at low engine speeds. Tomei engineers worked hard to produce camshafts that will deliver a well balanced profile at 1.3-1.5 times more than the stock camshaft.
Quality Control
 |
Every camshaft is carefully built through these production processes. Plus, strict inspection will be given to them and only the highest quality products are shipped. |
Surface Coating
Coating the surface of camshaft with manganese phosphate in order to protect from damage even when the camshaft has not lubricated yet. This has done by steeping press process that produces 0.5mm to 15 micromillimeter thin of manganese phosphate coating on its surface to prevent from direct contact with other metal parts while realizing smooth operation.
CNC Super Precise High Speed Grinding
The combination of a ultra high-speed main bearing and diamond grindstone is controlled by the computer. By using the same special-purpose machine as an automaker, high precision grinding is realized though in 1/3 period of time. Consequently, incredible accuracy of profile and remarkable price were realized at the same time.
Wavy Groove Finish by Oscillation Grinding
 |
Wavy groove is curved to the cam profile surface by oscillation during cam grinding process. Oil pool that is formed on the cam profile surface reduces a friction loss and prevents locking. |
Authentic Provenance Guarantee
Direct sourced genuine component with manufacturer serialization. No reproductions or unauthorized copies.
EU VAT Inclusive (€234.95)
Full EU tax invoice provided with every order conforming to Directive 2006/112/EC under VAT ID DE 349 201 892.
Expert Technical Support
Contact our Berlin engineering desk (+49 30 89201820) or WhatsApp (+49 30 89201820) for fitment verification prior to dispatch.
MATCHING TOMEI JAPAN HARDWARE
View All Tomei Japan Parts →
Related Performance Parts
Tomei Japan
Tomei Japan 2JZ36KIT Stroker Kit 87.0mm Standard Compression (With Bearings) 250018
SKU: 250018
€7,337.95
incl. 19% VAT
View →
Tomei Japan
Tomei Japan 2JZ36KIT Stroker Kit 87.0mm Standard Compression (No Bearings) 252004
SKU: 252004
€7,043.95
incl. 19% VAT
View →
€4,864.95
incl. 19% VAT
View →
€4,475.95
incl. 19% VAT
View →